Dreamcast-Talk.com

@megavolt85
HORIPAD SWITCH Controller Debug Report: (note: some mappings are different compared to the Retro-Bit Legacy16 gamepad i.e. d-pad) Amazon (US):
https://www.amazon.com/Nintendo-Switch- ... 01NAUATSM/

megavolt85 wrote: ↑Fri May 03, 2024 8:02 pm

maonaluva wrote: ↑Fri May 03, 2024 6:36 pm This one.

if is have wired connection try it

It has a micro usb connection, I tested it on Linux and it works normally, but not on USB4MAPLE unfortunately.

Do you only need VID and PID for 360 accessories? I have the Hori RAP and officially licensed 360 stick which would be cool to add (I assume the flight stick might be tricky to add). Sonik has helped me try and capture some full logs from some HID devices, it's so hard! Some times it doesn't show the 'Desc' but I can still get input byte lines (sorry, complete amateur when talking about this). Trying to get the Raphnet N64/GC to USB and the Mayflash Gamecube adapter logs, fingers crossed my stupid brain can figure it out.

Side note: the 360 flight stick works with the Magic S Pro 2, not sure it's properly setup tho, didn't properly check.

see the first message on this page, MoeFoh posted PuTTY.HoriS.debug.log.txt, this is the log from which I can add controller support.

maonaluva wrote: ↑Sat May 04, 2024 10:45 am It has a micro usb connection, I tested it on Linux and it works normally, but not on USB4MAPLE unfortunately.

To be honest, I have no ideas, they gave me a log, I added support, three users said that this controller works for them without problems.
Without a log I can’t tell why it doesn’t work for you

Thanks for the awesome work megavolt. Any chance you could add support to this MW2 Xbox 360 controller? Love using it for sentimental reasons. Thanks again!

VID - 0x0738
PID - 0xB726

kbrew904 wrote: ↑Sat May 04, 2024 7:48 pm Any chance you could add support to this MW2 Xbox 360 controller?

only if you make log

MoeFoh wrote: ↑Fri May 03, 2024 8:40 pm HORIPAD SWITCH Controller

test it
hot key - HOME
A - standart controller
B - FPS mode
X - all button and axis
Y - TWIN stick
L1 - ASCII stick
R1 - Arcade stick

@megavolt85
8bitdo NEOGEO with debug.
Displays the message:

"*** PANIC ***
Invalid Speed"

When I first plug into the controller. Is this message generated from your firmware or from the microcontroller itself.

Using latest debug firmware.

@megavolt85
Would it be possible to make a special one-off build for the wired xbox 360 support in which (for the Guide + A mode (default DC controller mode), LB & RB are currently ignored):

LB maps to a fully depressed LT
RB maps to a fully depressed RT

Would be useful for fighting games.

This is how the StrikerDC works.

megavolt85 wrote: ↑Sat May 04, 2024 8:11 pm

MoeFoh wrote: ↑Fri May 03, 2024 8:40 pm HORIPAD SWITCH Controller

test it
hot key - HOME
A - standart controller
B - FPS mode
X - all button and axis
Y - TWIN stick
L1 - ASCII stick
R1 - Arcade stick
usb4maple_05.05.24.7z

OMG! HELL YES!

Only one change:

Twin Stick mode (2nd d-pad)

Right Stick Up is showing down.
Right Stick Down is showing up.

Right Stick left & right are good.